ying 在三星 S10 E 的工程固件里扒出一些文件,找到一些可能适用于调试手机的拨号指令。
这些指令不一定是所有三星手机都通用的,各位小伙伴自测。
指令 | 标题 | 描述 |
---|---|---|
*#0*# | General Test Mode | 通用测试模式 |
*#33725327# | EFS Clear | Clear EFS partition (清空 EFS 分区) |
*#27663368378# | NV Rebuild | NV rebuild (重建 NV) |
*#6648# | NV Viewer | NV Viewer (NV 查看器) |
*#7547# | Test History | Test history NV list |
*#0589# | Light Sensor Ver | Light sensor test, Display light level(1,2,3) by Lux value |
*#5238973# | LcdTypeInfo | Display LCD type |
*#2663# | F/W Ver | Display TSP, TouchKey, SensorHub, Wifi, Bluetooth FW version, Update menu available |
*#3264# | Ram Ver | Display ram version (显示内存版本) |
*#12580*369# | Detail Ver | Display AP,CP,RF Cal, HW Rev (显示AP,CP,RF Cal,硬件版本) |
*#1234# | Simple Ver | Display AP,CP version (显示AP,CP 版本) |
*#99732# | Build Info | Display Build Time, Changelist (显示编译时间,Changelist) |
*#9999# | Simple Ver TMO | Display AP,CP,FTA SW VERSION for TMO Version only (显示AP,CP,FTA 软体版本(仅适用T-Mobile)) |
*#0782# | RTCTime | Display date, time, PDA RTC Get (显示日期时间) |
*#86824# | TSK F/W Ver | Display touchkey FW information, FW update function available, Touchkey sensitivity test, High sensitivity mode (触控键信息) |
*#4378873# | Gesture Sensor | Gesture Sonsor test, Display A,B,C,D Value, check Direction. (手势传感器) |
*#0588# | Proxi Test | Proximity sensor test (接近传感器测试) |
*#1004# | Sound Source Test | Test stereo, left ,right speaker by six music (音源测试) |
*#7769# | Proximity Offset | Display proximity sensor value, Set Low, High Threshold (显示接近传感器的偏移量) |
*#435517# | Grip Sensor | Select Grip Sensor, Calibration available (选择握力传感器,可校准) |
*#1106# | Grip On/Off | Grip Sensor On,Off (握力传感器开关) |
*#7736# | S-Pen Detection Test | S-Pen detection test. Display count (S-Pen 检测测试) |
*#77368378# | S-Pen Simple Test | S-Pen test on grid panel, Show values(X,Y,Pressure) |
*#77361379# | S-Pen 3 Menu Test | S-Pen test, Accuracy/Pressure, Linearity, Hover Accuracy menu available |
*#3736# | S-Pen 2 Menu Test | S-Pen test, AccuracyPont,Pressure, Line linearity menu available |
*#8778378# | TSP Test | output TSP, Hover data to SD Card, Hover Accuracy Test (触摸传感器面板测试?) |
*#877# | Result of TSP | Display Result of TSP |
*#46837# | Glove Touch Test | TSP High sensitivity mod test(TSP test while wearing glove) |
*#8778378# | TSP Test mode | output TSP, Hover data to SD Card, Hover Accuracy Test |
*#80# | Touch Noise | Touch noise test |
*#251# | TSK ON | Light on software key (开启按键灯?) |
*#250# | TSK OFF | Light off software key (关闭按键灯?) |
*#0228# | Battery Status | Display battery status(Current,Avaerage Value of Voltage, Temperature, Level, Level Block), Quickstart function available(Fuelgauge reset) (电子状态(可校准?))) |
*#350# | Reboot | Perform Reboot (重启) |
*#4327# | HDCP Check | HDCP check |
*#22235# | Acc Cal | Display accelerometer value(X,Y,Z), Calibration function available (显示加速器数据,可校准) |
*#0842# | Vibration, SVD_LED | Vibration test, Vibration value adjustable, SVC_LEC test, led rgb value adjustable (震动测试) |
*#0673# | Melody | Speaker, Receiver, Headset, Receiver_Headset, OFF menu available, Beeping |
*#2664# | Pointer Locaion | Check touch point location |
*#9998*3288# | Counter Print | Display TACounter, EPenCounter, EarjackCounter, QwertyCounter, FlashPopupCounter, TMBCounter value by Toast |
*#767*2878# | Qwerty Slide Reset | reset Qwerty Slide counter value |
*#0283# | Loopback Test | Check RCV, SPK, Earphone Loopback |
*#7328735824# | Lot ID | Display Lot ID |
*#22228378# | Cabc/Outside Test | Cabc On,Off Available, Outside Mode On,Off Available |
*#1105# | Fail History | Display Fail Histroy |
*#726387# | PCM Dump | PCM Dump, Record Test |
*#26732875# | Core CTRL | Core(CPU) Control |
*#272447# | AP Chip Test | Display AP Chip Test, PVS, IDDQ value |
*#6364366633# | Mdnie On/Off | Mdnie On,Off |
*#0775# | RCV/SPK Test | RCV,SPK test by 200,500,1000hz |
*#7594# | Shutdown Setting | Shutdown, 1 Key Hard Reset setting available |
*#272886# | Auto Answer Device | Auto Answer Without Device On,Off setting available (自动应答设备) |
*#2288379# | Fuel Gauge Register | Setting Fuel Gauge |
用法:打开手机的拨号
应用,直接键入指令即可(无需拨出)。
水平有限,欢迎小伙伴更正/补充。